Page Legal Restrictions On Copying Copyrighted works without permission of the copyright owner In addition, it is prohibited under any circumstances to copy domestic or foreign currencies, or works of art, without permission of the copyright owner. When in doubt about the nature of a document, consult with legal counsel. For details on their operation, refer to the pages indicated.
Copies 1-sided copies p. Reverse p. Detection Mixed Originals p. Detection function is available when the copier is equipped with an Automatic Document Feeder option. Automatic Document Feeder AF option Automatically feeds originals one page after another for scanning.
Printer Controller Pie option A built-in type printer controller that allows the copier to be used as a printer with the copier connected to a personal computer. Page 34 Holds the original against the Original Glass. Original Glass Place your original on this glass to allow the copier to scan it.
The original is to be placed face down. Page Inside The Copier Forms a copy image. The Imaging Unit is to be replaced only by your Tech. Pressure Lever Use to clear a misfed sheet of paper at the Fusing Unit. Page Options Description Bypass Tray Up to 50 sheets of plain paper or 20 sheets of special paper can be loaded on this tray.
Upper Copy Tray Receives printed pages produced via the personal computer or faxes received. Lower Copy Tray Receives copies made. Page Control Panel Pos. Page Icons On The Control Panel Blinks or lights up when the time approaches that copier needs maintenance service. Call your Tech. Add Paper indicator Lights up when the paper source currently selected for use runs out of paper.
Add Toner indicator Lights up when toner will soon run out. Pressing the [Start] key at this time will not immediately start the copy cycle. Refer to the conversion rate below. Page Useful Functions The length of time before the copier automatically resets itself can be set between 1 min and 5 min, in addition to 30 seconds.
The Auto Panel Reset function can even be disabled. Page Energy Saver If a document is loaded and the [Start] key is pressed during the period after the copier has been turned ON but before it is ready to make copies, the copier will automatically start the copy cycle as soon as it completes the warm-up cycle. Page Interrupting Copy Jobs If the current tray runs out of paper during a copy cycle and there is another tray loaded with paper of the same size and in the same direction, the copier will automatically select that tray to continue copying.
Page Account Number The account number entry screen changes to the default setting indication, indicating that the copier is ready to make copies. Run the desired copy cycle. When the copy cycle is completed, press the [Access] key a second time. Sending and Receiving Faxes Using the Copier When the optional Fax unit is mounted, fax transmission can be made using this copier.
For details of operation, refer to the Fax unit User Manual, separately available. Consult your Tech. The copier may not be able to detect, or may detect of any other size or irregular size. Page 54 Automatic Document Feeder. Page Mixed Originals E. Load the originals face up in the Document Feeder Tray. Page 56 Press the [Original] key to light the Mixed Orig. Press the [Start] key to start feeding and copying the originals from the top page.
Do not attempt to push the Original Glass with excessive force, as a malfunction could result. Make the necessary settings. Page Highly Transparent Originals Place a blank sheet of paper of the same size over the original. Do not look directly at the Original Glass surface during a scanning sequence since a strong beam of light is emitted.
This light beam is not, however, a laser beam and is not as dangerous. Make the Book Separation setting. Page Making Copies The following procedure describes how to place an original and make a basic copy of it. Making a Basic Copy Position the original. Page 63 Enter the number of copies to be made from the Key Pad. Any number from 1 to 99 can be entered. Press the [Start] key. Removal of the DC Power Supply Paper Take - Up Roll Cleaning of the Paper Separator Roll Cleaning of the Paper Take - Up Roll Cleaning of the Paper Dust Remover Cleaning of the Bypass Transport Roller Cleaning of Mirrors Cleaning of the Lens Cleaning of the CCD Sensor Removal of the CCD Unit Removal of the Scanner Drive Cables Winding of the Scanner Drive Cables Removal of the PH Unit Unit IU.
Application of Toner Cleaning of the Charge Neutralizing Plate Removal of the Fusing Unit Disassembly of the Fusing Unit Removal of the Separator Roll Assy Removal of the Paper Take-Up Roll Cleaning of the Paper Take-Up Roll Removal of the Main Board Paper Detecting Board Function Mode Choice Mode Adjust Mode Printer CD Registration Adjustment Printer FD Registration Adjustment Scanner CD Registration Adjustment Scanner FD Registration Adjustment Scanner CD Zoom Adjustment Scanner FD Zoom Adjustment Manual Bypass Registration Adjustment Sleeve Roller Db Adjustment There is no possibility of danger from a laser, provided the machine is serviced according to the instruction in this manual.
The laser diode and the scanning polygon mirror are incorporated in the print head unit. Therefore, the print head unit should not be opened under any circumstances. Food and Drug Administration of the U. This means that the device does not produce hazardous laser radiation. Use of controls, adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure.
Klasse 1 laser produkt der opfylder IEC sikkerheds kravene. Laser safety label. Red painted screws show that the assembly or unit secured can only be adjusted or set at the factory and shall not be readjusted, set, or removed in the field.
If it becomes unavoidably necessary to disassemble any of these assemblies and units, disassembly may be done provided that the conditions permitting reassembly are met. Note also that when two or more screws are used on the part in question, only one representative screw may be marked with red paint.
Unplug all connectors but PJ20 from the Master Board. Remove four screws and the Master Board. Unplug all connectors from the Control Board. Remove six screws and the Control Board. Remove the harness from seven wiring saddles and two edge covers. Unplug three connectors from the High Voltage Unit and remove the harness from one wiring saddle.
Remove the harness from one wiring saddle of the High Voltage Unit cover. Remove nine screws and the High Voltage Unit cover. Unplug two connectors from the High Voltage Unit. Remove two screws and the High Voltage Unit. Unplug two connectors of the Hopper Assy. Remove two Hopper mounting screws on the right.
Remove two Hopper mounting screws on the left and the Hopper Assy. Remove three screws and the Power Supply Right Cover. Remove four screws and the Power Supply Left Cover.
Unplug one connector and remove the harness from one edge cover. Unplug one connector and remove the harness from one wiring saddle. Unplug three connectors and remove the harness from two wiring saddles. Ver FrameMaker Clean when the Paper Dust Remover is full of paper dust for paper of other types. The maintenance cycle in the table represents the number of copies made in the standard copy mode A4C, 2PJ which may differ depending on conditions in which the copiers are used among different users.
Remove two screws and the Paper Separator Roll Assy. Press down the Paper Lifting Plate. Remove the Paper Separator Roll Assy. Using a soft cloth dampened with alcohol, wipe the Paper Separator Roll clean of dirt. Using a soft cloth dampened with alcohol, wipe the Paper Take-Up Roll clean of dirt. Using a soft cloth dampened with alcohol, wipe the Right and Left Synchronizing Rollers clean of dirt. Remove two screws and the stopper. Remove three screws and the Paper Dust Remover Assy. My Files.
Shopping Cart. There are currently no reviews for this product. This schematic will also work for the Radio Shack DX This is the full blown service manual complete with alignment instructions, schematics, and parts lists.
I thought I wouldn't be able to find manual for such rare equipment like KME. And here it is! Thanks for fast service! For details on their operation, refer to the pages indicated. Copies 1-sided copies p. Reverse p. Detection Mixed Originals p. Detection function is available when the copier is equipped with an Automatic Document Feeder option. Standard on Di Automatic Document Feeder AF option Automatically feeds originals one page after another for scanning.
Printer Controller Pie option A built-in type printer controller that allows the copier to be used as a printer with the copier connected to a personal computer. Page 35 Holds the original against the Original Glass. Original Glass Place your original on this glass to allow the copier to scan it.
The original is to be placed face down. Page Inside The Copier Forms a copy image. The Imaging Unit is to be replaced only by your Tech. Pressure Lever Use to clear a misfed sheet of paper at the Fusing Unit. Page Options Description Bypass Tray Up to 50 sheets of plain paper or 20 sheets of special paper can be loaded on this tray. Upper Copy Tray Receives printed pages produced via the personal computer or faxes received.
Lower Copy Tray Receives copies made. Page Control Panel Pos. Page Icons On The Control Panel Blinks or lights up when the time approaches that copier needs maintenance service. Call your Tech. Add Paper indicator Lights up when the paper source currently selected for use runs out of paper.
Add Toner indicator Lights up when toner will soon run out. Pressing the [Start] key at this time will not immediately start the copy cycle. Page Useful Functions The length of time before the copier automatically resets itself can be set between 1 min and 5 min, in addition to 30 seconds. The Auto Panel Reset function can even be disabled.
Page Energy Saver If a document is loaded and the [Start] key is pressed during the period after the copier has been turned ON but before it is ready to make copies, the copier will automatically start the copy cycle as soon as it completes the warm-up cycle. Page Interrupting Copy Jobs If the current tray runs out of paper during a copy cycle and there is another tray loaded with paper of the same size and in the same direction, the copier will automatically select that tray to continue copying.
Page Account Number The account number entry screen changes to the default setting indication, indicating that the copier is ready to make copies. Run the desired copy cycle. When the copy cycle is completed, press the [Access] key a second time.
Sending and Receiving Faxes Using the Copier When the optional Fax unit is mounted, fax transmission can be made using this copier. For details of operation, refer to the Fax unit User Manual, separately available. Consult your Tech. The copier may not be able to detect, or may detect of any other size or irregular size. Page 55 Automatic Document Feeder. Load the originals face up in the Document Feeder Tray so that their rear edges are in correct alignment with the Document Guide Plate.
Page 57 Press the [Original] key to light the Mixed Orig. Press the [Start] key to start feeding and copying the originals from the top page. Do not attempt to push the Original Glass with excessive force, as a malfunction could result. The maximum load resistance of the Original Glass is 3 kg. Make the necessary settings. Page Highly Transparent Originals Place a blank sheet of paper of the same size over the original.
Do not look directly at the Original Glass surface during a scanning sequence since a strong beam of light is emitted. This light beam is not, however, a laser beam and is not as dangerous. Make the Book Separation setting. Page Making Copies The following procedure describes how to place an original and make a basic copy of it.
Making a Basic Copy Position the original. Page 64 Enter the number of copies to be made from the Key Pad. Any number from 1 to 99 can be entered. Press the [Start] key. This will start the copy cycle.
0コメント